ALEPH Durable Request To Exit Motion Detector With Wall Or Ceiling Mounted OD22;

ALEPH OD22: REQUEST-TO-EXIT Passive Infrared Sensor

3. DETECTION PATTERN

4. INSTALLATION

Mounting Procedure

1. Select a mounting location over the center of the door or doors to be covered. Mount the detector on the ceiling wall or door frame.

2. Remove the front cover from the detector.

3. Loosely mount the back cover to the mounting surface using the supplied mounting screws.

4. Aim the detector for the desired coverage.

. Mount the front cover on the detector.

Long Range/Short Range Adjustment

The OD-22 can be set to detect individuals at either a long rang(several steps from the door) or at short range (immediately in front of the door).If the build- ing includes a lengthy approach to the exit doorway and no other foot traffic in the area, choose the long range setting.

Setup and Testing

1. Apply power to the unit.

2. Wait at least 3 min for the detector to settle.

3. Test the unit by walking directly through the coverage area toward the door.

4. Aim the detector up or down if necessary to obtain the proper coverage.

5. Check that the relay latch time is sufficient to adjust if necessary.

6. After confirming proper operation, replace the cover and walk test one more time to ensure the coverage has not changed.

6. WIRING

Latch Time

DIP Switch 1,2, and 3 set the relay time. Latch time is adjustable from 0.5 sec to 64 sec. It indicates the amount of time the relay can remain active after the detector first sees motion.

Table1: Latch Time DIP Switch Settings
Time(sec)	Switch 1			Switch 2	Switch 3
0.5(Default)	OFF			OFF	OFF
1	ON			OFF	OFF
2	OFF			ON	OFF
4	ON			ON	OFF
8	OFF			OFF	ON
16	ON			OFF	ON
32	OFF			ON	ON
64	ON			ON	ON

Table 2: LED Enable/Disable DIP Switch Settings
Switch 4			Function
OFF			Disabled
ON			Enabled (Default)

Table 3:Relay Mode DIP Switch Settings
Switch 5			Function
OFF			Fail Secure
ON			Fail safe(Default)

Table 4:Resettable/Non-resettable DIP Switch Settings
Switch 6			Function
OFF			Non-resettable
ON			Resettable (Default)

7. TROUBLE SHOOTING AND MAINTENANCE

TROUBLE		TROUBLE CAUSE							REMEDY
the unit does not power up		No or low input power.							Apply proper input voltage.
		Input power polarity reversed.							Correct wiring polarity.
Alarm LED does not light		the LED jumper is set to “LED OFF”.							Set LED jumper to “LED ENABLE”
		Incorrect sensor mounting height							Increase /decrease mounting height
LED indicates light,no signal output		Incorrect wiring at output terminals							Correct wiring fault.
		Lightning damage							Replace sensor.
Unit continues to operate after the input power has been disconnected.		The wire to the “V-” power input was discon- nected, the “V+” is still connected.							Disconnect wire from the “V+” power input.

MAINTENANCE

INSPECTION: An inspection of this unit should be made periodically, consisting of but not limited to all mounting, wiring

and the condition of the interior area and components.

CLEANING: Clean the plastic parts of this unit with a soft, clean, cloth dampened with water.

TESTING: This unit should be tested routinely for proper operation. At a minimum,operation should be fully checked yearly.

AIN Technology (Shenzhen) Co., Ltd. is an international enterprise which is exclusively designated and authorized by ALEPH Group to sell ALEPH brand security products, door magnetic switches, and Panther 4000, which is a wireless security systerm. AIN has set up production bases and branches in China (Shenzhen, Zhuhai), Japan, Europe, the United States and many other countries.
ALEPH brand alarm equipment, door magnetic switches and Baoping'an smart home security products which are researched and developed by AIN Technology have been all over the world. Especially the independently researched and developed active infrared intrusion detector which is the first in the world has been leading the development and innovation of the infrared industry for China, even the world.

AIN has a professional R&D team and high-quality management personal, annually invests more than 15% of the operating income in research and development and has two major product series of “ALEPH” and AIN.
AIN has won the honor of a&s Top Ten International Brands for ALEPH security products for many years. Furthermore, AIN is the designate supplier of infrared detection products of Vanke Group. Its products have been widely used in government agencies, airports, nuclear power plants, factories, residential estates and so on.
AIN has passed the following international quality system certifications : ISO9001:2008, ISO14001: 2004 and
QC080000:2012; product certification: CCC, CQC, UL, CE, FCC, etc.