Product Details
Company Profile

1024x768 TFT Color LCD Display 350 Nits Full Viewing Angle 220 Pins Lvds

15 Inch Lcd Display 1024x768 Full Viewing Angle Lvds Interface 20 Pins

General Description:

DV150X0M-N10 is a color active matrix TFT LCD MDL using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This MDL has a 15 inch diagonally measured active area with XGA resolutions (1024 horizontal by 768 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD MDL panel is adapted for a low reflection and higher color type.

Features:

LVDS interface with 1 pixel / clock
High-speed response
Low color shift image quality
6-bit +FRC color depth, display 16.7M colors
Wide viewing angle
DE (Data Enable) only mode
ADS technology is applied for high display quality
RoHS compliant

Specifications:

Parameter	Specification	Unit	Remarks
Active area	304. 128(H) × 228.096(V)	mm
Number of pixels	1024(H) × 768(V)	pixels
Pixel pitch	0.297(H) × 0.297(V)	mm
Pixel arrangement	Pixels RGB Vertical stripe
Display colors	16.7M	colors	6bits+FRC
Display mode	Normally Black
Dimensional outline	326.5(H) × 253.5(V) × 9.7(Total)	mm	Detail refer to drawing
Weight	930	g
Power Consumption	8.72	Watt	Typ.
Bezel width (L/R/U/D)	10/10/11.7/11.7	mm
Surface Treatment	Haze 25%, 3H
Back-light	E-LED Light bar Type
LED life	50000
Display Direction	landscape & Portrait

Absolute Maximum Ratings:

The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table.

Parameter	Symbol	Min.	Max.	Unit	Remark
Power Supply Voltage	VDD	-0.3	4	V	Ta = 25℃
Operating Temperature	TOP	-20	+70	℃	Note 1
Storage Temperature	TSUR	-20	+70	℃
Storage Temperature	TST	-20	+70	℃
Operating Ambient Humidity	Hop	10	90	%RH
Storage Humidity	Hst	10	90	%RH

Note 1 : Wet bulb temperature should be 39℃ max. and no condensation of water.

Electrical Specifications:

Parameter		Symbol	Values			Unit	Remark
Parameter		Symbol	Min	Typ	Max	Unit	Remark
Power Supply Input Voltage		VDD	3.0	3.3	3.6	V	Note 1
Power Supply Current		IDD	-	410	740	mA	Note 1
Power Supply Ripple Voltage		VRP	-	-	300	mV
Rush Current		IRUSH	-	2	3	A	Note 2
LVDS Interface	Differential Input High Threshold Voltage	VLVTH	-	-	+100	mV	VLVC=1.2V
	Differential Input Low Threshold Voltage	VLVTL	- 100	-	-	mV	VLVC=1.2V
	Common Input Voltage	VLVC	0.7	-	1.6	V
CMOS Interface	Input High Threshold Voltage	VIH	0.7VDD	-	VDD	V
CMOS Interface	Input Low Threshold Voltage	VIL	0	-	0.3VDD	V
Power Consumption		PD		0.8	1.3	W
		PBL		7.92	8.71		Note 3
		Ptotal		8.72	10.1

Note 1 : The supply voltage is measured and specified at the interface connector of LCM.The current draw and power consumption specified is for VDD=3.3V,Test Pattern of power supply current.

Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min).

Note 3 :Calculated value for reference (Input pins*VPIN × IPIN) excluding inverter loss.

Backlight Electrical Specifications:

Parameter			Min.	Typ.	Max.	Unit	Remarks
LED Driver Power Supply Voltage		HVDD	10.8	12	12.6	V
LED Driver Power Supply Current		IHVDD	550	600	700	mA
EN Control Level	Backlight on	VENH	3	3.3	3.6	V	EN logic high voltage
EN Control Level	Backlight off	VENL	0	0	0.6	V	EN logic low voltage
PWM Control Level	PWM High Level	VPML	3	3.3	3.6	V
PWM Control Level	PWM Low Level	VPML	0	0	0.6	V
PWM Control Frequency		F PWM	0.12	-	20	KHz	Refer to customer comments
Duty Ratio		-	5	-	100	%
LED Life-Time		N/A	50,000	-	-	Hour	Note4
LED Light Bar Input Voltage Per Input Pin		VPIN	32.4	36	39.6	V
LED Light Bar Input Current Per Input Pin		IPIN	-	55	-	mA	Note2
LED Power Consumption		PBL	-	7.92	8.71	W	Note3

LED bar consists of 48LED packages,4 strings(parallel)*12packages(serial)

Note1: There are one light bar ,and the specified current is input LED chip 100% duty current

Note2: The sense current of each input pin is 55mA

Note3: PBL=4 Input pins*VPIN × IPIN

Note4: The lifetime is determined as the time at which luminance of LED become 50% of the initial brightness or not normal lighting at IPIN=55mA on condition of continuous operating at 25 ± 2℃

Interface Connection:

Pin No	Symbol	Description	Pin No	Symbol	Description
1	VDD	Power Supply, 3.3V(typ.)	11	RIN2-	-LVDS differential data input 2
2	VDD	Power Supply,3.3V(typ.)	12	RIN2+	+LVDS differential data input 2
3	VSS	Ground	13	VSS	Ground
4	NC	No Connection	14	CLKIN-	-LVDS differential clock input CLK
5	RIN0-	-LVDS differential data input 0	15	CLKIN+	+LVDS differential clock input CLK
6	RIN0+	+LVDS differential data input 0	16	VSS	Ground
7	VSS	Ground	17	RIN3-	-LVDS differential data input 3
8	RIN1-	-LVDS differential data input 1	18	RIN3+	+LVDS differential data input 3
9	RIN1+	+LVDS differential data input 1	19	VSS	Ground
10	VSS	Ground	20	NC	No Connection

Optical Specification:

Parameter			Symbol	Condition	Min	Typ	Max	Unit	Remark
Viewing Angle	Horizontal		Θ3	CR > 10	85	89		Deg.	Note 1
	Horizontal		Θ9		85	89		Deg.
	Vertical		Θ12		85	89		Deg.
	Vertical		Θ6		85	89		Deg.
Brightness			Lv	Θ = 0. ILED=55m A	315	350		nit
Uniformity		9 Points	ΔY9	Θ = 0. ILED=55m A	75%	80%			Note 2
Contrast ratio			CR	Θ = 0.	700:1	1000:1	-		Note 3
Reproduction of color		White	Wx	Θ = 0. (Center) Normal Viewing Angle	TYP. - 0.03	0.313	TYP. + 0.03		Note 4
		White	Wy			0.329
		Red	Rx			0.649
		Red	Ry			0.338
		Green	Gx			0.323
		Green	Gy			0.627
		Blue	Bx			0.155
		Blue	By			0.056
Color Gamut					67	72	-	%
Response Time		Tr+Tf			-	30	35	ms	Note 5
Gamma Scale					2.0	2.2	2.4

Note :

1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o‟clock direction and the vertical or 6, 12 o‟clock direction with respect to the optical axis which is normal to the LCD surface.

2. The White luminance uniformity on LCD surface is then expressed as : ΔY =Minimum Luminance of 9 points / Maximum Luminance of 9 points.(see Figure 1 shown in Appendix).

3. Contrast measurements shall be made at viewing angle of 9= 0.and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See Figure 2 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically.

4. The color chromaticity coordinates specified in Table 9.shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. The BLU is used by BOE.

5. Response time Tg is the average time required for display transition by switching the input signal as below table and is based on Frame rate fV =60Hz to optimize.

Operating Precautions:

1.Do not connector or disconnect the cable to/from the Module at the “Power On” Condition.

2.When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the module would be damaged.

Product Tags:


*From:	Your email address is incorrect!
*To:	Shenzhen FRIDA LCD Co., Ltd
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!

Categories	TFT Color LCD Display
Brand Name:	BOE
Model Number:	DV150X0M-N10
Certification:	ROHS
Place of Origin:	CHINA
MOQ:	10pcs
Payment Terms:	T/T
Supply Ability:	5000pcs
Delivery Time:	5-8 work days
Packaging Details:	14pcs/box original package
Price:	USD49
Outline Dimension:	326.5(H) × 253.5(V) × 9.7(T)mm
Active Area:	304.128(H) × 228.096(V)mm
Number of Pixels:	1024(H) × 768(V)
Luminance:	350 nits
Viewing Angle:	89/89/89/89
Color Gamma:	72%